logo
Welkom bij ESTEL (GUANGDONG) TECHNOLOGY CO., LTD.
+8613752765943 / 86-0755 23592644

Mitigating EMI and Thermal Crossover in Substation Automation Retrofits

2026/11/16

Het laatste nieuws van het bedrijf over Mitigating EMI and Thermal Crossover in Substation Automation Retrofits

Mitigating EMI and Thermal Crossover in Substation Automation Retrofits

 

 

Background

 

A utility operator was modernizing a series of aging distribution substations. The upgrade required installing new intelligent electronic devices (IEDs), protection relays, and communication gateways to support remote monitoring and automated fault isolation.

 

In the past, the utility had housed all electrical control and communication equipment in a single, shared enclosure. However, as the substations became denser with high-voltage switchgear, the operators began noticing an increase in intermittent signal errors and unexplained communication dropouts.

 

The root cause was traced to the physical proximity of the sensitive control electronics to the high-power switching equipment and inverters. Heat generated by the power components was also impacting the reliability of the communication gear, especially during summer peak load periods.

 

 

The Challenge: Isolation Without Expanding the Footprint

 

The utility needed to physically separate the power equipment from the sensitive control and communication modules. However, the existing concrete pads at the substations were strictly limited in size. Expanding the footprint with a second cabinet was not an option, as it would require civil works, new permits, and extended downtime.

 

Additionally, the environment was highly corrosive. Located near an industrial zone, the substations were exposed to dust, humidity, and chemical particulates. The enclosures needed to maintain a tight seal to protect the electronics, while still allowing for adequate cooling.

Finally, the installation required a safe and reliable method for moving the heavy, fully loaded cabinets into position on the raised pads.

 

 

The Solution: A Dual-Compartment Isolation Enclosure

 

To solve these constraints, the operator selected a 42U Dual-Compartment Outdoor Electrical Cabinet. This design provided the required physical separation within a single, unified footprint.

 

1. Physical and Electromagnetic Isolation


The cabinet is divided into two completely independent 42U chambers, each with its own front door and standard 19-inch mounting rails. The utility used one compartment for the power conversion and battery systems, and the other for the IEDs, relays, and communication gateways.

 

This dual-chamber structure effectively separated the heat sources and reduced electromagnetic interference (EMI) from the power equipment, stabilizing the signal integrity of the control gear. It also improved safety, ensuring that maintenance on the high-voltage side could be performed without exposing the communication modules to unnecessary risk.

 

2. Heavy-Duty Environmental Protection


The enclosure was specified with 1.5mm galvanized steel for the shell and doors, but critically, it utilized 304 stainless steel for all fasteners, screws, nuts, and rivets. This detail was essential for the corrosive industrial environment, preventing the hardware from seizing or rusting over time.

 

Rated IP65, the cabinet's rubber gaskets provided a fully sealed, dust-tight environment that protected the electronics from water jets and particulate ingress. The RAL7035 powder coating added an extra layer of UV and corrosion resistance.

 

3. Installation and Accessibility


Despite being a dual-compartment design, the cabinet was built as a single floor-standing unit with a pallet base for forklift access. Optional lifting eyes were used to crane the unit onto the substation pads, simplifying the installation process.

 

Once in place, the independent doors allowed technicians to access either side without opening the other, maintaining the thermal and environmental isolation of the control compartment even during routine power maintenance.

 

 

The Outcome

 

The dual-compartment design allowed the utility to consolidate the necessary equipment on space-constrained pads without risking signal interference or thermal issues. The use of 304 stainless steel fasteners and the IP65 sealing ensured that the equipment remained protected from the industrial environment.

 

By separating the high-power and control subsystems, the utility significantly reduced the intermittent communication dropouts that had plagued the legacy single-enclosure setups, while also simplifying maintenance procedures for field technicians.